Product ID:5-MINUTES EPOXY HARDENER
MSDS Date:01/08/1990
FSC:8040
NIIN:01-034-0401
Kit Part:Y
MSDS Number: BLJMB

Emergency Phone: 508-777-1100

Info Phone: 508-777-1100

Cage: 16509

Telephone: 508-777-1100

Cage: 16509

2,4,6-TRI(DIMETHYLAMINOMETHYL) PHENOL (DMP)

CAS: 90-72-2

RTECS: SN3500000

Fraction By Weight: 10-30%

0 LBS/GAL (EPA REFERENCE METHOD 24)

RTECS: 9999999VO

LD50 LC50 Mixture:ORAL LD50 (RAT):DMP: 1653 MG/KG *
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PROLONGED OR SEVERE OVEREXPOSURE TO
DMP VAPOR CAN CAUSE DELAYED LUNG DAMAGE AND CHEMICAL PNEUMONIA.
PROLONGED OR REPEATED CONTACT WITH 5-MINUTE EPOXY HARDENER MAY
CAUSE SKIN IRRITATION. *DERMAL LD50 (RABBIT):DMP: 1350 MG/KG.
INHALATION LC50 (RAT): DMP: >0.5 MG/LITER:EXPOSURE TIME:HOURS.
Effects of Overexposure:EYES:HARDENER CAN CAUSE MODERATE TO SEVERE EYE
IRRIT.SKIN:ANIMAL TESTS ON 5-MIN EPOXY HARDENER HAVE SHOWN IT TO
CAUSE LITTLE OR NO SKIN IRRIT.INHALATION:DMP VAPOR CAN CAUSE IRRIT
OF THE RSPRTRY TRACT. INGESTION:DMP IS SLIGHTLY TOXIC BY
INGESTION;TOXIC BY INGESTION:MUSCLE WEAKNESS,LABORED BREATHING &
GASTRIC IRRIT.

First Aid:EYES:FLUSH EYE WITH CLEAN WATER FOR AT LEAST 15 MINUTES WHILE
GENTLY HOLDING EYELIDS OPEN. GET IMMEDIATE MEDICAL ATTENTION.
SKIN:REMOVE CONTAMINATED CLOTHING AND SHOES. WASH THOROUGHLY WITH
SOAP AND W ARM WATER. CONSULT A PHYSICIAN IF IRRITATION DEVELOPS.
INHALATION:REMOVE PATIENT TO FRESH AIR. INGESTION:DO NOT INDUCE
VOMITING. CONSULT A PHYSICIAN.

Flash Point Method:TCC
Flash Point:300F,149C
Extinguishing Media:CO2, DRY CHEMICAL, FOAM
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR SELF-CONTAINED
BREATHING APPARATUS AND PROTECTIVE CLOTHING IN CONFINED AREAS.
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:ABSORB SPILL ON INERT MATERIAL SUCH AS SAND OR
VERMICULITE AND TRANSFER TO AN IMPERMEABLE CONTAINER.

Handling and Storage Precautions:STORE WELL CLOSED IN A COOL,DRY
PLACE.KEEP HANDS AWAY FROM EYES WHEN HANDLING THIS HARDENER,OR
BEFORE WASHING AFTER USE.

Respiratory Protection:NONE REQUIRED IN NORMAL USE WITH PROPER
VENTILATION.
Ventilation:LOCAL EXHAUST IS RECOMMENDED FOR CONFINED AREAS. GENERAL
MECHANICAL VENTILATION IS ADEQUATE FOR NORMAL USE.
Protective Gloves:CHEMICAL RESISTANT RUBBER GLOVES.
Eye Protection:SAFETY GLASSES WITH SIDESHIELDS.
Work Hygienic Practices:WASH THOROUGHLY AFTER USING, PARTICULARLY
BEFORE EATING OR SMOKING.
Supplemental Safety and Health
THIS INFO APPLIES TO HARDENER PART OF KIT. AFTER CURING, THE PRODUCT IS
NON-HAZARDOUS.

Vapor Pres:< 1
Spec Gravity:0.97
pH:9.5/5%
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS, AMBER LIQUID WITH SULFUROUS ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:OPEN FLAME AND EXTREME HEAT.
Hazardous Decomposition Products:OXIDES OF CARBON, OXIDES OF SULFUR,
OXIDES OF NITROGEN.
Conditions to Avoid Polymerization:WHEN THIS HARDENER IS MIXED WITH AN
EPOXY RESIN HEAT IS GENERATED, BE CAREFUL WHEN MIXING MORE THAN AN
OUNCE OR SO.

Waste Disposal Methods:REMOVE TO A WASTE DISPOSAL FACILITY OPERATING IN
COMPLIANCE WITH STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.